How To Repair Broken Irrigation Pipe

Download Article

Download Article

If in that location are areas of your backyard that wait more similar to a marsh than a lawn, you lot may have broken sprinkler pipes. Fortunately, fixing the problem isn't too hard if yous don't mind getting dirty.

Steps

1. one

   Ensure you have all the required supplies. Nothing is worse than having to run to the hardware store in the middle of a project. Encounter the list of things you need beneath.

2. 2

   Find the rupture. Normally a soggy expanse of grass, only sometimes information technology is a geyser.

   Advertisement

3. 3

   Turn off the sprinklers, if y'all don't this could be a very hard task.

4. 4

   Dig upwardly the pipe. Not the whole pipe, just the department that is broken. Advisedly remove the section of grass higher up the pipe, trying to continue it intact. Do this by cutting a circular section with the terminate of your shovel above where you are to dig and then advisedly lifting it off. Dig up the dirt to a higher place the bad pipage with a shovel (you will probably as well demand a hand trowel to dig upwardly the dirt under the pipe). You will want to accept at least 6 inches (15.2 cm) on each side of the break clear and enough room for yous fist underneath the pipe. If the hole fills with water, yous will either take to wait for it to dry out or bail information technology out (the latter is recommended).

5. 5

   Cutting the piping. Go a hacksaw, PVC or metal pipage cutters (depending on what type of piping yous accept, older sprinkler systems are usually metallic, while newer ones tend to be PVC). Cut the broken section out so that you have clean, undamaged pipage on both sides.

6. six

   Measure a new length of pipe that is just a bit shorter than the gap left by one-time pipe that you lot cut away. Information technology should probably be 1/2 " to 1" shorter to allow room for the connectors. Or you can buy a PVC fitting from most home improvement stores that has 1 pipe sliding inside an outer butt with an O-ring inside. It volition extend most three" in length. You may meet in stores 1/ii" to two 1/2" in diameter sizes. Ane cease is a female person sideslip and the other is a male that needs a coupling, elbow, or tee to connect to complete the repair.

7. vii

   Clean the pipe. Some h2o will come up pouring out at first, you could try to catch it, but information technology is easier to bail it out. One time the water stops coming out, make clean both ends with a rag.

8. eight

   Fit the new section. If you are lucky plenty to take PVC then y'all just put the PVC primer and gum on the outside of the pipe and inside of the straight connectors and skid them together. Piece of work rapidly because the glue sets fast. Then put the section you just glued in the gap y'all just created, repeating the gluing procedure. If you accept metallic pipes you volition have to thread the outside of the pipage to fit the connectors rather than gluing them.

9. 9

   Examination the pipe. Plow the sprinklers back on and brand certain it is sealed properly.

10. 10

    If everything is fixed, cover upward the hole and replace the grass yous so advisedly removed before.

    Advertisement

Inquire a Question

200 characters left

Include your email address to go a message when this question is answered.

Submit

Advertisement

Thanks for submitting a tip for review!

• Exist conscientious when digging, you never know what y'all might hit with your shovel.

Ad

Things You'll Demand

• Shovel & trowel
• Pipe
• ii straight connectors
• hacksaw or pipe cutter
• for PVC, glue and primer
• for metal, a threader
• Rags
• two Hours

Nearly This Article

Thanks to all authors for creating a page that has been read 51,808 times.

Did this article help you?

How To Repair Broken Irrigation Pipe,

Source: https://www.wikihow.com/Fix-a-Broken-Sprinkler-Pipe

Posted by: youngweneary.blogspot.com

Share this post